View LMR62014_9036564.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LMR62014 www.ti.com snvs735a ? october 2011 ? revised november 2011 LMR62014 simple switcher ? 20vout, 1.4a step-up voltage regulator in sot-23 check for samples: LMR62014 1 features description the LMR62014 switching regulator is a current-mode 23 ? input voltage range of 2.7v to 14v boost converter operating at fixed frequency of ? output voltage up to 20v 1.6 mhz. ? switch current up to 1.4a the use of sot-23 package, made possible by the ? 1.6 mhz switching frequency minimal power loss of the internal 1.4a switch, and ? low shutdown iq, < 1 a use of small inductors and capacitors result in the industry's highest power density. the LMR62014 is ? cycle-by-cycle current limiting capable of greater than 90% duty cycle, making it ? internally compensated ideal for boosting to voltages up to 20v. ? 5-pin sot-23 packaging (2.92 x 2.84 x 1.08mm) these parts have a logic-level shutdown pin that can ? fully enabled for webench ? power designer be used to reduce quiescent current and extend battery life. performance benefits protection is provided through cycle-by-cycle current ? extremely easy to use limiting and thermal shutdown. internal compensation simplifies design and reduces component count. ? tiny overall solution reduces system cost applications ? boost conversions from 3.3v, 5v, and 12v rails ? space constrained applications ? embedded systems ? lcd displays ? led applications system performance efficiency vs load current efficiency vs load current v in = 3.3v, v out = 12v v in = 5v, v out = 12v 1 please be aware that an important notice concerning availability, standard warranty, and use in critical applications of texas instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. 2 simple switcher, webench are registered trademarks of texas instruments. 3 all other trademarks are the property of their respective owners. production data information is current as of publication date. copyright ? 2011, texas instruments incorporated products conform to specifications per the terms of the texas instruments standard warranty. production processing does not necessarily include testing of all parameters. 0 20 40 60 80 100 120 140 160 load (ma) 0 10 20 30 40 50 60 70 80 efficiency (%) efficiency (%) load current (ma) 0 100 200 300 400 70 80 90 100 500
LMR62014 snvs735a ? october 2011 ? revised november 2011 www.ti.com connection diagram figure 1. 5-lead sot-23 (top view) see dbv package pin descriptions pin name function 1 sw drain of the internal fet switch. 2 gnd analog and power ground. 3 fb feedback point that connects to external resistive divider. 4 shdn shutdown control input. connect to vin if the feature is not used. 5 v in analog and power input. 2 submit documentation feedback copyright ? 2011, texas instruments incorporated product folder links: LMR62014 LMR62014 sw fb gnd v in shdn u1 r3 51k shdn gnd 5v in c1 2.2 p f l1/10 p h r2 13.3k cf 220 pf d1 r1/117k c2 4.7 p f 12v out 500 ma (typ)
formula: if power dissipation exceeds the maximum specified above, the internal thermal protection LMR62014 www.ti.com snvs735a ? october 2011 ? revised november 2011 these devices have limited built-in esd protection. the leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the mos gates. absolute maximum ratings (1) (2) storage temperature range ? 65 c to +150 c operating junction temperature range ? 40 c to +125 c lead temp. (soldering, 5 sec.) 300 c power dissipation (3) internally limited fb pin voltage ? 0.4v to +6v sw pin voltage ? 0.4v to +22v input supply voltage ? 0.4v to +14.5v shdn pin voltage ? 0.4v to vin + 0.3v j-a (sot-23) 265 c/w esd rating human body model (4) 2 kv for soldering specifications see snoa549 (1) absolute maximum ratings indicate limits beyond which damage to the component may occur. electrical specifications do not apply when operating the device outside of the limits set forth under the operating ratings which specify the intended range of operating conditions. (2) if military/aerospace specified devices are required, please contact the texas instruments sales office/ distributors for availability and specifications. (3) the maximum power dissipation which can be safely dissipated for any application is a function of the maximum junction temperature, t j (max) = 125 c, the junction-to-ambient thermal resistance for the sot-23 package, j-a = 265 c/w, and the ambient temperature, t a . the maximum allowable power dissipation at any ambient temperature for designs using this device can be calculated using the circuitry will protect the device by reducing the output voltage as required to maintain a safe junction temperature. (4) the human body model is a 100 pf capacitor discharged through a 1.5 k ? resistor into each pin. copyright ? 2011, texas instruments incorporated submit documentation feedback 3 product folder links: LMR62014
LMR62014 snvs735a ? october 2011 ? revised november 2011 www.ti.com electrical characteristics limits in standard typeface are for t j = 25 c, and limits in boldface type apply over the full operating temperature range ( ? 40 c t j +125 c). unless otherwise specified: v in = 5v, v shdn = 5v, i l = 0a. symbol parameter conditions min (1) typical (2) max (1) units v in input voltage 2.7 14 v v out (min) minimum output voltage r l = 43 ? (3) v in = 2.7v 5.4 7 v under load v in = 3.3v 8 10 v in = 5v 13 17 r l = 15 ? (3) v in = 2.7v 3.75 5 v in = 3.3v 5 6.5 v in = 5v 8.75 11 i sw switch current limit see (4) 1.8 2 a 1.4 r ds (on) switch on resistance i sw = 100 ma, vin = 5v 260 400 m ? 500 i sw = 100 ma, vin = 3.3v 300 450 550 shdn th shutdown threshold device on 1.5 v device off 0.50 i shdn shutdown pin bias current v shdn = 0 0 a v shdn = 5v 0 2 v fb feedback pin reference v in = 3v 1.205 1.230 1.255 v voltage i fb feedback pin bias current v fb = 1.23v 60 500 na i q quiescent current v shdn = 5v, switching 2 3.0 ma v shdn = 5v, not switching 400 500 a v shdn = 0 0.024 1 v fb fb voltage line regulation 2.7v v in 14v 0.02 %/v v in f sw switching frequency (5) 1 1.6 1.85 mhz d max maximum duty cycle (5) 86 93 % i l switch leakage not switching v sw = 5v 1 a (1) limits are ensured by testing, statistical correlation, or design. (2) typical values are derived from the mean value of a large quantity of samples tested during characterization and represent the most likely expected value of the parameter at room temperature. (3) l = 10 h, c out = 4.7 f, duty cycle = maximum (4) switch current limit is dependent on duty cycle (see typical performance characteristics ). (5) specified limits are the same for vin = 3.3v input. 4 submit documentation feedback copyright ? 2011, texas instruments incorporated product folder links: LMR62014
LMR62014 www.ti.com snvs735a ? october 2011 ? revised november 2011 typical performance characteristics unless otherwise specified: v in = 5v, shdn pin tied to v in . iq vin (active) vs temperature oscillator frequency vs temperature figure 2. figure 3. max. duty cycle vs temperature iq vin (idle) vs temperature figure 4. figure 5. feedback bias current vs temperature feedback voltage vs temperature figure 6. figure 7. copyright ? 2011, texas instruments incorporated submit documentation feedback 5 product folder links: LMR62014 feedback voltage (v) 1.222 1.223 1.224 1.225 1.226 1.227 1.228 1.229 1.23 1.231 -40 -25 0 25 50 75 100 125 temperature ( o c) max duty cycle (%) 92.1 92.2 92.3 92.4 92.5 92.6 92.7 92.8 92.9 93 temperature ( o c) v in = 5v v in = 3.3v -50 -25 0 25 50 75 100 125 150 temperature ( o c) feedback bias current ( p a) 0 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 -50 -25 0 25 50 75 100 125 150 i q v in (idle) ( p a) temperature ( o c) 340 345 350 355 360 365 370 375 380 -50 -25 0 25 50 75 100 125 150 -50 -25 0 25 50 75 100 125 150 temperature ( o c) 1.8 1.85 1.9 1.95 2 2.05 2.1 2.15 2.2 i q v in active (ma) oscillator frequency (mhz) 1.4 1.42 1.44 1.46 1.48 1.5 1.52 1.54 1.56 1.58 temperature ( o c) v in = 5v v in = 3.3v -50 -25 0 25 50 75 100 125 150
LMR62014 snvs735a ? october 2011 ? revised november 2011 www.ti.com typical performance characteristics (continued) unless otherwise specified: v in = 5v, shdn pin tied to v in . r ds (on) vs temperature current limit vs temperature figure 8. figure 9. efficiency vs load current r ds (on) vs v in v in = 2.7v, v out = 5v figure 10. figure 11. efficiency vs load current efficiency vs load current v in = 3.3v, v out = 5v v in = 4.2v, v out = 5v figure 12. figure 13. 6 submit documentation feedback copyright ? 2011, texas instruments incorporated product folder links: LMR62014 70 0 0 100 200 300 400 500 600 load (ma) efficiency (%) 0 10 20 30 40 50 60 70 80 90 100 1400 0 200 400 600 800 1000 1200 load (ma) efficiency (%) 0 10 20 30 40 50 60 70 80 90 100 2.5 3.5 4.5 5.5 6.5 7.5 8.5 9.5 v in (v) 0 50 100 150 200 250 300 350 r ds_on (m : ) 0 50 100 150 200 250 300 load (ma) efficiency (%) 0 10 20 30 40 50 60 70 80 90 100 r ds(on) ( : ) -40 -25 0 25 50 75 100 125 temperature ( o c) 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 vin = 5v vin = 3.3v current limit (a) 2 2.1 2.2 2.3 2.4 2.5 2.6 -40 -25 0 25 50 75 100 125 temperature ( o c)
LMR62014 www.ti.com snvs735a ? october 2011 ? revised november 2011 typical performance characteristics (continued) unless otherwise specified: v in = 5v, shdn pin tied to v in . efficiency vs load current efficiency vs load current v in = 2.7v, v out = 12v v in = 3.3v, v out = 12v figure 14. figure 15. efficiency vs load current efficiency vs load current v in = 5v, v out = 12v v in = 5v, v out = 18v figure 16. figure 17. copyright ? 2011, texas instruments incorporated submit documentation feedback 7 product folder links: LMR62014 0 20 40 60 80 100 120 140 160 load (ma) 0 10 20 30 40 50 60 70 80 efficiency (%) 350 0 50 100 150 200 250 300 load (ma) efficiency (%) 0 10 20 30 40 50 60 70 80 90 100 600 0 100 200 300 400 500 load (ma) efficiency (%) 0 10 20 30 40 50 60 70 80 90 100 0 10 20 30 40 50 0 10 20 30 40 50 60 70 80 efficiency (%) load (ma)
LMR62014 snvs735a ? october 2011 ? revised november 2011 www.ti.com block diagram 8 submit documentation feedback copyright ? 2011, texas instruments incorporated product folder links: LMR62014
LMR62014 www.ti.com snvs735a ? october 2011 ? revised november 2011 theory of operation the LMR62014 is a switching converter ic that operates at a fixed frequency (1.6 mhz) for fast transient response over a wide input voltage range and incorporates pulse-by-pulse current limiting protection. because this is current mode control, a 33 m ? sense resistor in series with the switch fet is used to provide a voltage (which is proportional to the fet current) to both the input of the pulse width modulation (pwm) comparator and the current limit amplifier. at the beginning of each cycle, the s-r latch turns on the fet. as the current through the fet increases, a voltage (proportional to this current) is summed with the ramp coming from the ramp generator and then fed into the input of the pwm comparator. when this voltage exceeds the voltage on the other input (coming from the gm amplifier), the latch resets and turns the fet off. since the signal coming from the gm amplifier is derived from the feedback (which samples the voltage at the output), the action of the pwm comparator constantly sets the correct peak current through the fet to keep the output voltage in regulation. q1 and q2 along with r3 - r6 form a bandgap voltage reference used by the ic to hold the output in regulation. the currents flowing through q1 and q2 will be equal, and the feedback loop will adjust the regulated output to maintain this. because of this, the regulated output is always maintained at a voltage level equal to the voltage at the fb node "multiplied up" by the ratio of the output resistive divider. the current limit comparator feeds directly into the flip-flop that drives the switch fet. if the fet current reaches the limit threshold, the fet is turned off and the cycle terminated until the next clock pulse. the current limit input terminates the pulse regardless of the status of the output of the pwm comparator. application hints selecting the external capacitors the best capacitors for use with the LMR62014 are multi-layer ceramic capacitors. they have the lowest esr (equivalent series resistance) and highest resonance frequency which makes them optimum for use with high frequency switching converters. when selecting a ceramic capacitor, only x5r and x7r dielectric types should be used. other types such as z5u and y5f have such severe loss of capacitance due to effects of temperature variation and applied voltage, they may provide as little as 20% of rated capacitance in many typical applications. always consult capacitor manufacturer ? s data curves before selecting a capacitor. selecting the output capacitor a single ceramic capacitor of value 4.7 f to 10 f will provide sufficient output capacitance for most applications. if larger amounts of capacitance are desired for improved line support and transient response, tantalum capacitors can be used. aluminum electrolytics with ultra low esr such as sanyo oscon can be used, but are usually prohibitively expensive. typical ai electrolytic capacitors are not suitable for switching frequencies above 500 khz due to significant ringing and temperature rise due to self-heating from ripple current. an output capacitor with excessive esr can also reduce phase margin and cause instability. in general, if electrolytics are used, it is recommended that they be paralleled with ceramic capacitors to reduce ringing, switching losses, and output voltage ripple. selecting the input capacitor an input capacitor is required to serve as an energy reservoir for the current which must flow into the coil each time the switch turns on. this capacitor must have extremely low esr, so ceramic is the best choice. we recommend a nominal value of 2.2 f, but larger values can be used. since this capacitor reduces the amount of voltage ripple seen at the input pin, it also reduces the amount of emi passed back along that line to other circuitry. copyright ? 2011, texas instruments incorporated submit documentation feedback 9 product folder links: LMR62014
LMR62014 snvs735a ? october 2011 ? revised november 2011 www.ti.com feed-forward compensation although internally compensated, the feed-forward capacitor cf is required for stability (see basic application circuit ). adding this capacitor puts a zero in the loop response of the converter. the recommended frequency for the zero fz should be approximately 6 khz. cf can be calculated using the formula: cf = 1 / (2 x x r1 x fz) (1) selecting diodes the external diode used in the typical application should be a schottky diode.the diode must be rated to handle the maximum output voltage and load current. a 20v diode such as the mbr0520 is recommended. the mbr05xx series of diodes are designed to handle a maximum average current of 0.5a. for applications exceeding 0.5a average, a toshiba crs08 can be used. layout hints high frequency switching regulators require very careful layout of components in order to get stable operation and low noise. all components must be as close as possible to the LMR62014 device. it is recommended that a 4-layer pcb be used so that internal ground planes are available. as an example, a recommended layout of components is shown: figure 18. recommended pcb component layout some additional guidelines to be observed: 1. keep the path between l1, d1, and c2 extremely short. parasitic trace inductance in series with d1 and c2 will increase noise and ringing. 2. the feedback components r1, r2 and cf must be kept close to the fb pin of u1 to prevent noise injection on the fb pin trace. 3. if internal ground planes are available (recommended) use vias to connect directly to ground at pin 2 of u1, as well as the negative sides of capacitors c1 and c2. 10 submit documentation feedback copyright ? 2011, texas instruments incorporated product folder links: LMR62014
LMR62014 www.ti.com snvs735a ? october 2011 ? revised november 2011 setting the output voltage the output voltage is set using the external resistors r1 and r2 (see basic application circuit ). a value of approximately 13.3 k ? is recommended for r2 to establish a divider current of approximately 92 a. r1 is calculated using the formula: r1 = r2 x (v out /1.23 ? 1) (2) figure 19. basic application circuit duty cycle the maximum duty cycle of the switching regulator determines the maximum boost ratio of output-to-input voltage that the converter can attain in continuous mode of operation. the duty cycle for a given boost application is defined as: (3) this applies for continuous mode operation. inductance value the first question we are usually asked is: ? how small can i make the inductor? ? (because they are the largest sized component and usually the most costly). the answer is not simple and involves trade-offs in performance. larger inductors mean less inductor ripple current, which typically means less output voltage ripple (for a given size of output capacitor). larger inductors also mean more load power can be delivered because the energy stored during each switching cycle is: e = l/2 x (lp) 2 where ? ? lp ? is the peak inductor current. (4) an important point to observe is that the LMR62014 will limit its switch current based on peak current. this means that since lp(max) is fixed, increasing l will increase the maximum amount of power available to the load. conversely, using too little inductance may limit the amount of load current which can be drawn from the output. best performance is usually obtained when the converter is operated in ? continuous ? mode at the load current range of interest, typically giving better load regulation and less output ripple. continuous operation is defined as not allowing the inductor current to drop to zero during the cycle. it should be noted that all boost converters shift over to discontinuous operation as the output load is reduced far enough, but a larger inductor stays ? continuous ? over a wider load current range. copyright ? 2011, texas instruments incorporated submit documentation feedback 11 product folder links: LMR62014 duty cycle = v out + v diode - v in v out + v diode - v sw
LMR62014 snvs735a ? october 2011 ? revised november 2011 www.ti.com to better understand these trade-offs, a typical application circuit (5v to 12v boost with a 10 h inductor) will be analyzed. we will assume: v in = 5v, v out = 12v, v diode = 0.5v, v sw = 0.5v (5) since the frequency is 1.6 mhz (nominal), the period is approximately 0.625 s. the duty cycle will be 62.5%, which means the on time of the switch is 0.390 s. it should be noted that when the switch is on, the voltage across the inductor is approximately 4.5v. using the equation: v = l (di/dt) (6) we can then calculate the di/dt rate of the inductor which is found to be 0.45 a/ s during the on time. using these facts, we can then show what the inductor current will look like during operation: figure 20. 10 h inductor current, 5v ? 12v boost (LMR62014x) during the 0.390 s on time, the inductor current ramps up 0.176a and ramps down an equal amount during the off time. this is defined as the inductor ? ripple current ? . it can also be seen that if the load current drops to about 33 ma, the inductor current will begin touching the zero axis which means it will be in discontinuous mode. a similar analysis can be performed on any boost converter, to make sure the ripple current is reasonable and continuous operation will be maintained at the typical load current values. 12 submit documentation feedback copyright ? 2011, texas instruments incorporated product folder links: LMR62014
LMR62014 www.ti.com snvs735a ? october 2011 ? revised november 2011 maximum switch current the maximum fet switch current available before the current limiter cuts in is dependent on duty cycle of the application. this is illustrated in the graphs below which show typical values of switch current as a function of effective (actual) duty cycle: figure 21. switch current limit vs duty cycle calculating load current as shown in figure 20 which depicts inductor current, the load current is related to the average inductor current by the relation: i load = i ind (avg) x (1 - dc) where ? "dc" is the duty cycle of the application. (7) the switch current can be found by: i sw = i ind (avg) + ? (i ripple ) (8) inductor ripple current is dependent on inductance, duty cycle, input voltage and frequency: i ripple = dc x (v in -v sw ) / (f x l) (9) combining all terms, we can develop an expression which allows the maximum available load current to be calculated: (10) the equation shown to calculate maximum load current takes into account the losses in the inductor or turn-off switching losses of the fet and diode. for actual load current in typical applications, we took bench data for various input and output voltages that displayed the maximum load current available for a typical device in graph form: copyright ? 2011, texas instruments incorporated submit documentation feedback 13 product folder links: LMR62014 20 30 40 50 60 70 80 90 100 duty cycle (%) = [1 - eff*(v in / v out )] 0 500 1000 1500 2000 2500 3000 sw current limit (ma) v in = 5v v in = 3.3v v in = 2.7v v in = 3v i load (max) = (1 - dc) x (i sw (max) - dc (v in - v sw )) 2fl
LMR62014 snvs735a ? october 2011 ? revised november 2011 www.ti.com figure 22. max. load current (typ) vs v in design parameters v sw and i sw the value of the fet "on" voltage (referred to as v sw in the equations) is dependent on load current. a good approximation can be obtained by multiplying the "on resistance" of the fet times the average inductor current. fet on resistance increases at v in values below 5v, since the internal n-fet has less gate voltage in this input voltage range (see typical performance characteristics curves). above v in = 5v, the fet gate voltage is internally clamped to 5v. the maximum peak switch current the device can deliver is dependent on duty cycle. for higher duty cycles, see typical performance characteristics curves. thermal considerations at higher duty cycles, the increased on time of the fet means the maximum output current will be determined by power dissipation within the LMR62014 fet switch. the switch power dissipation from on-state conduction is calculated by: p (sw) = dc x i ind (ave) 2 x r ds (on) (11) there will be some switching losses as well, so some derating needs to be applied when calculating ic power dissipation. inductor suppliers recommended suppliers of inductors for this product include, but are not limited to sumida, coilcraft, panasonic, tdk and murata. when selecting an inductor, make certain that the continuous current rating is high enough to avoid saturation at peak currents. a suitable core type must be used to minimize core (switching) losses, and wire power losses must be considered when selecting the current rating. shutdown pin operation the device is turned off by pulling the shutdown pin low. if this function is not going to be used, the pin should be tied directly to v in . if the shdn function will be needed, a pull-up resistor must be used to v in (approximately 50k-100k ? recommended). the shdn pin must not be left unterminated. 14 submit documentation feedback copyright ? 2011, texas instruments incorporated product folder links: LMR62014 v in (v) max load current (ma) 0 200 400 600 800 1000 1200 2 3 4 5 6 7 8 9 10 11 v out = 5v v out = 8v v out = 10v v out = 12v v out = 18v
LMR62014 www.ti.com snvs735a ? october 2011 ? revised november 2011 figure 23. flash led application copyright ? 2011, texas instruments incorporated submit documentation feedback 15 product folder links: LMR62014 efficiency vs load current efficiency (%) load (ma) 0 50 100 150 200 250 0 10 20 30 40 50 60 70 80 90 100 300 3.3 - 9v boost LMR62014 sw fb gnd v in shdn u1 r3 51k shdn gnd 3.3 v in c1 2.2 p f r2 13.3k cf 330 pf d1 r1/84k l1/10 p h c2 4.7 p f d2 d3 d4 d5 r4 r5 9v out 240 ma (typ)
package option addendum www.ti.com 24-jan-2013 addendum-page 1 packaging information orderable device status (1) package type package drawing pins package qty eco plan (2) lead/ball finish msl peak temp (3) op temp (c) top-side markings (4) samples LMR62014xmf/nopb active sot-23 dbv 5 1000 green (rohs & no sb/br) cu sn level-1-260c-unlim -40 to 125 sh1b LMR62014xmfe/nopb active sot-23 dbv 5 250 green (rohs & no sb/br) cu sn level-1-260c-unlim -40 to 125 sh1b LMR62014xmfx/nopb active sot-23 dbv 5 3000 green (rohs & no sb/br) cu sn level-1-260c-unlim -40 to 125 sh1b (1) the marketing status values are defined as follows: active: product device recommended for new designs. lifebuy: ti has announced that the device will be discontinued, and a lifetime-buy period is in effect. nrnd: not recommended for new designs. device is in production to support existing customers, but ti does not recommend using this part in a new design. preview: device has been announced but is not in production. samples may or may not be available. obsolete: ti has discontinued the production of the device. (2) eco plan - the planned eco-friendly classification: pb-free (rohs), pb-free (rohs exempt), or green (rohs & no sb/br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. tbd: the pb-free/green conversion plan has not been defined. pb-free (rohs): ti's terms "lead-free" or "pb-free" mean semiconductor products that are compatible with the current rohs requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. where designed to be soldered at high temperatures, ti pb-free products are suitable for use in specified lead-free processes. pb-free (rohs exempt): this component has a rohs exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. the component is otherwise considered pb-free (rohs compatible) as defined above. green (rohs & no sb/br): ti defines "green" to mean pb-free (rohs compatible), and free of bromine (br) and antimony (sb) based flame retardants (br or sb do not exceed 0.1% by weight in homogeneous material) (3) msl, peak temp. -- the moisture sensitivity level rating according to the jedec industry standard classifications, and peak solder temperature. (4) only one of markings shown within the brackets will appear on the physical device. important information and disclaimer: the information provided on this page represents ti's knowledge and belief as of the date that it is provided. ti bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. efforts are underway to better integrate information from third parties. ti has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. ti and ti suppliers consider certain information to be proprietary, and thus cas numbers and other limited information may not be available for release. in no event shall ti's liability arising out of such information exceed the total purchase price of the ti part(s) at issue in this document sold by ti to customer on an annual basis.
tape and reel information *all dimensions are nominal device package type package drawing pins spq reel diameter (mm) reel width w1 (mm) a0 (mm) b0 (mm) k0 (mm) p1 (mm) w (mm) pin1 quadrant LMR62014xmf/nopb sot-23 dbv 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 q3 LMR62014xmfe/nopb sot-23 dbv 5 250 178.0 8.4 3.2 3.2 1.4 4.0 8.0 q3 LMR62014xmfx/nopb sot-23 dbv 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 q3 package materials information www.ti.com 26-jan-2013 pack materials-page 1
*all dimensions are nominal device package type package drawing pins spq length (mm) width (mm) height (mm) LMR62014xmf/nopb sot-23 dbv 5 1000 203.0 190.0 41.0 LMR62014xmfe/nopb sot-23 dbv 5 250 203.0 190.0 41.0 LMR62014xmfx/nopb sot-23 dbv 5 3000 206.0 191.0 90.0 package materials information www.ti.com 26-jan-2013 pack materials-page 2

important notice texas instruments incorporated and its subsidiaries (ti) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per jesd46, latest issue, and to discontinue any product or service per jesd48, latest issue. buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. all semiconductor products (also referred to herein as ? components ? ) are sold subject to ti ? s terms and conditions of sale supplied at the time of order acknowledgment. ti warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in ti ? s terms and conditions of sale of semiconductor products. testing and other quality control techniques are used to the extent ti deems necessary to support this warranty. except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. ti assumes no liability for applications assistance or the design of buyers ? products. buyers are responsible for their products and applications using ti components. to minimize the risks associated with buyers ? products and applications, buyers should provide adequate design and operating safeguards. ti does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which ti components or services are used. information published by ti regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from ti under the patents or other intellectual property of ti. reproduction of significant portions of ti information in ti data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. ti is not responsible or liable for such altered documentation. information of third parties may be subject to additional restrictions. resale of ti components or services with statements different from or beyond the parameters stated by ti for that component or service voids all express and any implied warranties for the associated ti component or service and is an unfair and deceptive business practice. ti is not responsible or liable for any such statements. buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of ti components in its applications, notwithstanding any applications-related information or support that may be provided by ti. buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. buyer will fully indemnify ti and its representatives against any damages arising out of the use of any ti components in safety-critical applications. in some cases, ti components may be promoted specifically to facilitate safety-related applications. with such components, ti ? s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. nonetheless, such components are subject to these terms. no ti components are authorized for use in fda class iii (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. only those ti components which ti has specifically designated as military grade or ? enhanced plastic ? are designed and intended for use in military/aerospace applications or environments. buyer acknowledges and agrees that any military or aerospace use of ti components which have not been so designated is solely at the buyer ' s risk, and that buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. ti has specifically designated certain components as meeting iso/ts16949 requirements, mainly for automotive use. in any case of use of non-designated products, ti will not be responsible for any failure to meet iso/ts16949. products applications audio www.ti.com/audio automotive and transportation www.ti.com/automotive amplifiers amplifier.ti.com communications and telecom www.ti.com/communications data converters dataconverter.ti.com computers and peripherals www.ti.com/computers dlp ? products www.dlp.com consumer electronics www.ti.com/consumer-apps dsp dsp.ti.com energy and lighting www.ti.com/energy clocks and timers www.ti.com/clocks industrial www.ti.com/industrial interface interface.ti.com medical www.ti.com/medical logic logic.ti.com security www.ti.com/security power mgmt power.ti.com space, avionics and defense www.ti.com/space-avionics-defense microcontrollers microcontroller.ti.com video and imaging www.ti.com/video rfid www.ti-rfid.com omap applications processors www.ti.com/omap ti e2e community e2e.ti.com wireless connectivity www.ti.com/wirelessconnectivity mailing address: texas instruments, post office box 655303, dallas, texas 75265 copyright ? 2013, texas instruments incorporated
mouser electronics authorized distributor click to view pricing, inventory, delivery & lifecycle information: texas instruments: ? LMR62014xmfdemo/nopb

▲Up To Search▲

Price & Availability of LMR62014

	To Download LMR62014 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .